Home > Dual Boot > Dual Boot With Raid + Non-Raid

Dual Boot With Raid + Non-Raid

Contents

As for the raid type, I believe it is in fact bios setup RAID and not pure hardware. If you install to the drives without this running you WILL have access to the section of the hard drive that the disk metadata is located on that the controller uses, edit: more info, if I yank the SATA cable on the Linux disk, and then power on, I get a grub rescue prompt. I updated the original posting for what I was able to do (Email me if you want the PDF version): My system is based on an ASUS motherboard which came with weblink

Then I entered their Intel raid BIOS and also used -ctrl+M for the other controller to make my RAID partitions. Thanks in advance! This document is constantly updated by users like you and is a "living" document to which your contributions are welcome. I mean I know it is, but can it be fixed after the install?

Dual Boot Raid 0

would i be able to remove my current 500GB drive, install the 2x 200gbs (Stripped/RAID0) along with a fresh OS the whole nine yards? One more thing, the laptop also has an extra 1TB HDD for data storage. Sharing (characters) is Caring!

If you have arrived here after researching this topic on the Internet, you know that a common response to this question is, "I don't know if you can actually do that, I encountered an error during Windows 7 installation during a couple of my attempts that said the Windows installer could not find or create a ‘system partition'. DistroUbuntu 16.04 Xenial Xerus Re: Dual Boot Windows 8.1 and Ubuntu 14.04 on RAID 0 Do not know enough about how well desktop currently would work with your configuration. The problem lies with Windows - it expects to be on the first drive.

Basically you install using the live cd (alternate no longer required in 9.10) then boot into the live cd to remove GRUB2 and install+configure GRUB legacy. Ubuntu Raid Boot I thought it would be easy to upgrade Grub to give me a menu to choose Linux or Windows, but sudo upgrade-grub and sudo os-prober both fails with: Error: ddf1 wrong Discussions Cyber Deals Vendor Discussion Forum Feedback Mod Hotline « Previous Thread | Next Thread » Forum Software Alternative Operating Systems A guide to Windows/Linux dual boot on RAID Posting Permissions http://superuser.com/questions/168551/raid-with-dual-boot Install and setup your RAID config3.

Linked 0 Which RAID controller should I use? I have not used the software raid and you would have to get some more info on it before you attempt it.If you are refering to the free software I linked I am not sure what other info is needed, please let me know, happy to clarify. more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science

Ubuntu Raid Boot

Join us to comment and to customize your site experience! http://askubuntu.com/questions/794851/dual-booting-16-04-and-window-10-with-raid-0 Follow these steps to install grub-customizer: sudo add-apt-repository ppa:danielrichter2007/grub-customizer sudo apt-get update sudo apt-get install grub-customizer You should now be able to boot into both Linux and Windows residing on the Dual Boot Raid 0 Install & Repair the grub boot loader Caveat: I was unable to get my machine to boot successfully to the ‘grub' menu at the conclusion of steps 1 - 10 as Fakeraid Tango Icons Tango Desktop Project.

The danger is that Boot Repair occasionally makes matters worse, particularly with exotic setups. have a peek at these guys This must be done from the command terminal before exiting and rebooting. The other 500 gig is a single mode Windows 7 install that never finished. http://en.wikipedia.org/wiki/RAID http://www.smallnetbuilder.com/nas/n...-is-not-backup I do not know much about RAID and then whether you have BIOS RAID which is called 'fakeRAID' as it is not hardware based. Dmraid

Others have NOT recommended setting up a separate boot partition - they couldn't get it to boot properly. worse comes to worse, i just have a spot to toss all of my old .iso's i can't bring myself to delete., i may bench them to find out for sure. Create the table as 'msdos', which will be selected by default. check over here These people shouldn't have to add a separate hard drive just so they can boot Linux.

alternatively you could test you raid array by running this $ sudo dmraid -tay6. Unless you are spinning 10/15k disks you are not going to see marked improvement. Or not fully implemented for RAID yet.

I like to use a program call Easy BCD.Then you just reboot your computer and you can choose to boot to either your new RAID setup or your 500GB HDD.(This is

This is what 'just works' for any modern setup. If 'fine /boot/grub/stage1' shows something else than 0,0, for example 1,0, then do 'root (hd1,0) 25. Hard disk fails in SCSI Non-Raid solved Restoring a Raid 0 Image to Non-Raid System solved Raid 1 Mirror to Non-Raid solved Asus P7P55D PRO RAID 0 + Non-RAID solved Raid Older Windows versions required a driver loaded during the Windows install process for these cards, but that is changing as it has already changed in FreeBSD (which has FakeRAID support built

The last is possibly the best, but you need make sure you select the righ options and do not overwrite any parts which windows already uses. (E.g. I was thinking I'd have a separate drive for each OS and NTFS for the RAID hard drives. Exit the terminal and click reboot, or type "shutdown -r now" at the terminal window * When the system comes back up login and verify that /dev/mapper/pdc_feddabdf (or whatever dmraid names this content Any tips would be much appreciated as I am growing angry at Ubuntu for making this so difficult and wasting so much of my time this week but at the same

I found the answer here: http://users.bigpond.net.au/hermanzone/p15.htm#Chainloading_Windows_using_map_commands The section is "Chainloading Windows on a non-first hard disk". You need to format all partitions from Linux. Hence my question about RAID. If a user deletes a file, it is instantly deleted from both drives (and therefor this does not provide a backup to restore the file.) The reason a mirror is the

I get a quick flash of a message and then a forced reboot before it finishes the installation. 3.