Home > Windows Xp > SATA Drive Detected As An Atapi Drive By Windows Xp Setup.

SATA Drive Detected As An Atapi Drive By Windows Xp Setup.

Contents

In 2012, voters passed a law that ensured residents' right to repair their car wherever they wanted. button: Install From Disk window will pop up. Check with your motherboard manufacturer for updated drivers. Intended audience 2. have a peek here

dammit. Get the answer edtrx09Aug 25, 2009, 9:15 AM Thanks for all your input...I had someone look at it and it turns out Sata can be used for secondary drive and It Related Resources 2 HDD -SATA & IDE-How to set them up Can't find your answer ? I now have drives with windows and after setting up the pin configuration to slave it still defaults to the ide hard drive when it boots ups. http://www.sevenforums.com/installation-setup/321876-sata-drive-detected-atapi-drive-windows-xp-setup.html

Change Ide To Ahci Windows 7

I installed a Western Digital 200 gb SATA drive in a windows XP system and it only sees 100gb. Very handy when things go wrong and I need to boot and run from a diagnostic tool kit on floppy. I had a similar problem with my other...

Check your motherboard/notebook driver CD, try to find F6 textmode AHCI driver for your chipset (southbridge). Just make sure your board will support both. Most drives are configured by default as Master devices. How To Enter Bios If you install a new optical drive in such an older system, connect the existing audio cable from the new drive to the audio adapter, but also enable digital audio.

We have a chance to guarantee our right to repair electronic equipment—like smartphones, computers, and even farm equipment. How To Change Sata Mode In Bios Proffitt Forum moderator / July 20, 2005 8:19 AM PDT In reply to: I'll be wary 2. by esemones / July 19, 2005 8:12 AM PDT My new computer has a SATA Maxtor drive as the primary.

Installation & Setup SATA DVD RW drive detected as cdromHi, Win7hp/32b.

My second choice is the first optical drive. Reboot And Select Proper Boot Device Our forum is dedicated to helping you find support and solutions for any problems regarding your Windows 7 PC be it Dell, HP, Acer, Asus or a custom build. Expand IDE ATA/ATAPI controllers, then right-click on Primary IDE Channel and choose Update Driver... It is completely separate from which drive unit acts as the boot drive called C:.

How To Change Sata Mode In Bios

Stand up for your right to repair. https://www.cnet.com/forums/discussions/mixing-sata-and-ide-drives-in-a-system-115142/ Learn more You're viewing YouTube in Turkish. Change Ide To Ahci Windows 7 Connect with us facebook twitter CNET Reviews Top Categories Best Products CNET 100 Appliances Audio Cameras Cars Desktops Drones Headphones Laptops Networking Phones Printers Smart Home Tablets TVs Virtual Reality Wearable Nlite If you find out any good info, please let me know...thanx!Regards,Robert Flag Permalink This was helpful (0) Collapse - Sata is primary by edersch / July 28, 2005 9:26 AM PDT

Substitute your particular name of AHCI driver instead of iastor as needed. http://lacosteradigital.com/windows-xp/how-to-install-windows-xp-sp2-in-usb.html I have OS's on both drives and can boot from either by selecting which one I want to be the primary at startup(note this will have an effect on drive letters). Flag Permalink This was helpful (0) Collapse - Feel free to make a new post. Enhanced mode device support must be set on to use a mixed device configuration. 0x0000007b

SYS file is a driver itself, CAT file is a catalog of digital signatures to verify integrity of the driver, and INF is an informational file for Windows operating system how Best answer PaperdocAug 18, 2009, 11:57 PM Your problem starts with misunderstanding how drives are identified and used. With two drives, the second MUST be set to Slave. Check This Out It makes me wonder on SATA drives if windows 98se can be installed onto logical partition.

All modern motherboards, optical drives, and operating systems support DMA modes, but DMA is not always enabled automatically. Bootmgr Is Missing I'm using 3 maxtor HD's 80 & 120 gb sata + 200 gb pata, and 3 dvd burners BENQ 1625, & 1610, + LG GSA 4163B. Figure 8-2: Mounting a rail on an optical drive 6.

If your case uses rails to mount optical drives, install the rails.

NOT SO.An IDE channel port and its cable support up to two drives. Then the Master will be whichever drive is plugged into the END connector, and the Slave will be the middle connector. by nelchael_com / November 22, 2006 5:48 AM PST In reply to: Same problem here... __[ In English, resume/summary ]______________________I get a HD SATA and want turn it the Primary Boot Windows Xp Download Prior settings of the jumpers to "slave" would result in no boot screen at all upon powering on.

Even if the operating system provides some extended function support, such as the CD burning applet included with Windows XP, you'll probably want to install more capable software to take full It is the one you set in the BIOS Setup screen for Boot Priority or Sequence. I read somewhere I need to set up bios to certain mode in order for it to read the Sata drive as the primary and the ide as the secondary drive. this contact form If I don't put a bootable disk in the floppy drive, it will go next to the DVD reader and try to find a bootable disk in there.

So now your Boot Drive is not necessarily the Primary Master.Enter SATA systems which include one very important difference.